|
|
Are these gapped right?
(Preview)
|
1972468bb
|
4
|
589
|
|
|
|
|
Noisy motor.
(Preview)
Ok so I got my motor back together and can't seem to get the valves adjusted right. Have done it every way possible and they are still super noisy. I'm ready to just burn the car where it sits. I was doing some reading on this and have read it could be piston slop? Or bad valve guides?
It's a Comp hydr. rolle...
|
1972468bb
|
12
|
507
|
|
|
|
|
got a front engine plate need help!!
(Preview)
can i run the front engine plate and solid tranny mount and be alright and maybe use an engine limiter .......or do ihave to buy a mid plate also ...id hate to do that cause im already adapting a glide to my 408 already !
i bought a aje tubular k member that has no motor mounts ,and uses a plate
|
5pointSlow
|
14
|
494
|
|
|
|
|
Failed Emissions terribly!
(Preview)
Just got my 89 Camaro back from inspection and emissions are way high.
Limits: Actual:
HC idle - 220 1485
HC 2500rpm - 220 1449
CO idle - 1.2 4.33
CO 2500rpm - 1.2 1.34
I know this means there is unburned fuel. When I get a chance I am going to check the timing and change the cat converter when I put on...
|
CamaroAddict
|
21
|
582
|
|
|
|
|
Fuel in oil
(Preview)
So I took my motor apart and the oil smells like fuel and is a grayish color. Any ideas how the fuel would be gettin in? Checked the carb and all the gaskets seem fine it was runnin rich but not that bad.
|
1972468bb
|
14
|
514
|
|
|
|
|
Good read about oil formula changes and wear
(Preview)
|
89Rustang
|
0
|
400
|
|
|
|
|
Dyno near Gardner,MA?`
(Preview)
Anyone know of one? Must be a Dynojet, Mustang dynos suck. There is a Mustang dyno 10 minutes from my house but I need better readouts for my A/F ratio. Within 30 minutes prefered.
Thanks,
|
89Rustang
|
6
|
448
|
|
|
|
|
Misfire only hot??????????????
(Preview)
I have a customer's 1998 camaro with a 350, ls-1.
it is misfiring on #4 only when at operating temp.
SO FAR is did a compression test cold ...ok
changed the spark plug and wire...
swapped the injector and coil with #2 and still has a misfire ,
only #4...
cold it's does not skip, and runs great COLD.
n...
|
JOHNNY93
|
6
|
515
|
|
|
|
|
Battery relo
(Preview)
Relocating my battery to trunk. Run wires under car or in car under carpet?
|
89Rustang
|
7
|
461
|
|
|
|
|
backcut spark plugs ??
(Preview)
some of you guys must be running these.
I was going to throw a fresh set in at the track last night (Autolite AR103's) but as soon as I went to gap them I figured I better stick to what has been working until I get more ifo.
now that the ground strap does not go over the electrode how do you go about gapping t...
|
murphinator
|
1
|
433
|
|
|
|
|
Oil blow by.
(Preview)
Ok so I put a new 950 Holley on and it has no vacuum ports so I can't run a pcv valve and I'm having crazy oil blow by. It blew the dip stick right out of the tube and oil every where. I don't really want to run a vacuum pump so can I tap into my manifold for the pcv set up? Any other suggestions?
|
1972468bb
|
9
|
488
|
|
|
|
|
anyone paint the lifter valley?
(Preview)
i hear they do it with glyptol paint its red electrical paint but its also used for painting
engine internals for increaed oil flow ??? anyone ever do this i would think paint would chip off
|
5pointSlow
|
11
|
487
|
|
|
|
|
An adapters.
(Preview)
Don't think this is really engine tech but I didn't know where else to put it. Anyone know where I can find an step downs? I have a fuel cell that has 8an and 10an fittings on it and I am running 8an now for my fuel line. I need to find an adapter to go from 8an to 6an so I can run my nos fuel line and one to go from 10an...
|
1972468bb
|
10
|
465
|
|
|